No, that was autoREconf, and all they are below 2.65:
marcusmae_at_teslatron:~/Programming/openmpi-r24785$ ls /usr/bin/autoreconf
autoreconf autoreconf2.13 autoreconf2.50 autoreconf2.59 autoreconf2.64
And default one points to 2.50:
marcusmae_at_teslatron:~/Programming/openmpi-r24785$ autoreconf -help
Usage: /usr/bin/autoreconf2.50 [OPTION]... [DIRECTORY]...
I don't know why, probably that's the default Debian Squeeze setup?
- D.
2011/12/30 Ralph Castain <rhc_at_[hidden]>:
> Strange - if you look at your original output, autoconf is identified as 2.50 - a version that is way too old for us. However, what you just sent now shows 2.67, which would be fine.
>
> Why the difference?
>
>
> On Dec 29, 2011, at 3:27 PM, Dmitry N. Mikushin wrote:
>
>> Hi Ralph,
>>
>> URL: http://svn.open-mpi.org/svn/ompi/trunk
>> Repository Root: http://svn.open-mpi.org/svn/ompi
>> Repository UUID: 63e3feb5-37d5-0310-a306-e8a459e722fe
>> Revision: 24785
>> Node Kind: directory
>> Schedule: normal
>> Last Changed Author: rhc
>> Last Changed Rev: 24785
>> Last Changed Date: 2011-06-17 22:01:23 +0400 (Fri, 17 Jun 2011)
>>
>> 1. Checking tool versions
>>
>> Searching for autoconf
>> Found autoconf version 2.67; checking version...
>> Found version component 2 -- need 2
>> Found version component 67 -- need 65
>> ==> ACCEPTED
>> Searching for libtoolize
>> Found libtoolize version 2.2.6b; checking version...
>> Found version component 2 -- need 2
>> Found version component 2 -- need 2
>> Found version component 6b -- need 6b
>> ==> ACCEPTED
>> Searching for automake
>> Found automake version 1.11.1; checking version...
>> Found version component 1 -- need 1
>> Found version component 11 -- need 11
>> Found version component 1 -- need 1
>> ==> ACCEPTED
>>
>> 2011/12/30 Ralph Castain <rhc_at_[hidden]>:
>>> Are you doing this on a subversion checkout? Of which branch?
>>>
>>> Did you check your autotoll versions to ensure you meet the minimum required levels? The requirements differ by version.
>>>
>>> On Dec 29, 2011, at 2:52 PM, Dmitry N. Mikushin wrote:
>>>
>>>> Dear Open MPI Community,
>>>>
>>>> I need a custom OpenMPI build. While running ./autogen.pl on Debian
>>>> Squeeze, there is an error:
>>>>
>>>> --- Found autogen.sh; running...
>>>> autoreconf2.50: Entering directory `.'
>>>> autoreconf2.50: configure.in: not using Gettext
>>>> autoreconf2.50: running: aclocal --force -I m4
>>>> autoreconf2.50: configure.in: tracing
>>>> autoreconf2.50: configure.in: not using Libtool
>>>> autoreconf2.50: running: /usr/bin/autoconf --force
>>>> configure.in:113: error: possibly undefined macro: AC_PROG_LIBTOOL
>>>> If this token and others are legitimate, please use m4_pattern_allow.
>>>> See the Autoconf documentation.
>>>> autoreconf2.50: /usr/bin/autoconf failed with exit status: 1
>>>> Command failed: ./autogen.sh
>>>>
>>>> It's a bit confusing, because automake, libtool, autoconf are
>>>> installed. What might be the other reasons of this error?
>>>>
>>>> Thanks,
>>>> - Dima.
>>>> _______________________________________________
>>>> users mailing list
>>>> users_at_[hidden]
>>>> http://www.open-mpi.org/mailman/listinfo.cgi/users
>>>
>>>
>>> _______________________________________________
>>> users mailing list
>>> users_at_[hidden]
>>> http://www.open-mpi.org/mailman/listinfo.cgi/users
>>
>> _______________________________________________
>> users mailing list
>> users_at_[hidden]
>> http://www.open-mpi.org/mailman/listinfo.cgi/users
>
>
> _______________________________________________
> users mailing list
> users_at_[hidden]
> http://www.open-mpi.org/mailman/listinfo.cgi/users
|
![[Flag]](../../../../../community/mirrors/flag-us.gif){kind=small}