Ok, I uninstalled the previous version. Then downloaded the pre-release version. Unpacked it, configure, make, make install....
When running MPICC I get this:
mpiCC: error while loading shared libraries: libopen-pal.so.0: cannot open shared object file: No such file or directory
$whereis libopen-pal
libopen-pal: /usr/local/lib/libopen-pal.so /usr/local/lib/libopen-pal.la
So the library exists. How can I make mpiCC know it's location?
Thanks!
Giovani
Giovani Faccin <giovanifaccin_at_[hidden]> escreveu: Yep, setting the card manually did not solve it.
I'm compiling the pre-release version now. Let's see if it works.
Giovani
Giovani Faccin <giovanifaccin_at_[hidden]> escreveu: Hi Mark
Compiler and flags:
sys-devel/gcc-4.1.2 USE="doc* fortran gtk mudflap nls (-altivec) -bootstrap -build -d -gcj (-hardened) -ip28 -ip32r10k -libffi% (-multilib) -multislot (-n32) (-n64) -nocxx -objc -objc++ -objc-gc -test -vanilla"
Network stuff:
sonja gfaccin # ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:33166 errors:0 dropped:0 overruns:0 frame:0
TX packets:33166 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:9846970 (9.3 Mb) TX bytes:9846970 (9.3 Mb)
wlan0 Link encap:Ethernet HWaddr 00:1C:BF:24:24:91
inet addr:192.168.1.50 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::21c:bfff:fe24:2491/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5944 errors:0 dropped:0 overruns:0 frame:0
TX packets:6343 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3058968 (2.9 Mb) TX bytes:1713598 (1.6 Mb)
wmaster0 Link encap:UNSPEC HWaddr 00-1C-BF-24-24-91-60-00-00-00-00-00-00-00-00
-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
I have 2 cards in my laptop, one is an ethernet one that's not enabled (no kernel modules loaded). The other one is the wireless card, which is enabled. Those 2 interfaces appear because the driver creates them. The real one is wlan0.
I'll try to find in the faq where is this flag to specify the card, just in case MPI might be trying to use wmaster0. Let's see if it works.
Thanks!
Giovani
Mark Kosmowski <mark.kosmowski_at_[hidden]> escreveu: Giovani:
Which compiler are you using?
Also, you didn't mention this, but does "mpirun hostname" give the
expected response? I (also new) had a hang similar to what you are
describing due to ompi getting confused as to which of two network
interfaces to use - "mpirun hostname" would hang when started on
certain nodes. This problem was resolved by telling ompi which
network interface to use (I forget the option needed to do this off
the top of my head, but it is in the FAQ somewhere).
Good luck,
Mark
_______________________________________________
users mailing list
users_at_[hidden]
http://www.open-mpi.org/mailman/listinfo.cgi/users
---------------------------------
Abra sua conta no Yahoo! Mail, o único sem limite de espaço para armazenamento! _______________________________________________
users mailing list
users_at_[hidden]
http://www.open-mpi.org/mailman/listinfo.cgi/users
---------------------------------
Abra sua conta no Yahoo! Mail, o único sem limite de espaço para armazenamento! _______________________________________________
users mailing list
users_at_[hidden]
http://www.open-mpi.org/mailman/listinfo.cgi/users
---------------------------------
Abra sua conta no Yahoo! Mail, o único sem limite de espaço para armazenamento!
|
![[Flag]](../../../../../community/mirrors/flag-us.gif){kind=small}